PJURE uses an advanced 5 + 1 Stage Filtration System, certified to NSF/ANSI 42 & 372, combining sediment filtration, activated carbon, UF membrane, KDF media, and a final mineralization layer.

It removes bacteria, chlorine, heavy metals, VOCs, PFAS, pharmaceuticals, and microplastics (down to ~1 µm) — while adding back natural minerals like calcium, magnesium, and potassium for a balanced, refreshing taste.

No — PJURE is designed to keep the good stuff.

While it removes harmful contaminants, it retains essential minerals and even adds trace amounts of calcium, magnesium, and potassium through its mineralization stage.

TDS (Total Dissolved Solids) refers to the total amount of dissolved minerals, salts, and metals naturally present in water — measured in ppm (parts per million) or mg/L.

It includes healthy minerals like calcium, magnesium, potassium, and sodium, which give water its natural taste and balance.

PJURE is designed to remove harmful substances while keeping beneficial minerals, so your TDS value stays stable — a good sign that your water is clean, safe, and naturally mineralized.

Reverse Osmosis (RO) pushes water through an ultra-fine membrane using high pressure. It removes almost everything — including contaminants and the natural minerals (like calcium and magnesium) that the body actually needs. The result is extremely pure water, but often too pure: it can become slightly acidic (pH below 7) and less hydrating.

PJURE, on the other hand, uses a 6-layer filtration system:

• 5 layers to purify (removing bacteria, heavy metals, VOCs, chlorine, etc.)
• 1 final layer to add minerals back in – helping the water reach a natural, slightly alkaline pH of ~7.5, which supports taste, hydration and overall wellbeing.
  

Unlike RO, PJURE doesn’t require electricity or a bulky pressure tank, making it compact and easy to install under any sink — in just 10 minutes.

👉 Read more in our full comparison blog post here

The flow rate is about 3.8 liters per minute, tested under 4.1 bar, which is typical water pressure in most European homes.

To put it simply, your existing water pressure stays the same with a steady water stream. No pressure drop, no weak trickle.

Your tap will work just like before, only better! Now with clean, mineral-rich water coming out.

Not at all — installation takes just a few minutes, and no plumber is needed.

Everything comes pre-assembled. Simply:

1. Connect the inlet hose to your cold-water line.
2. Connect the outlet hose to your faucet line.
3. Use the included 3/8” → 1/2” adapter set if needed(fits all EU hoses).
4. Turn on the water and flush for 5 minutes before first use.

Yes — the filter fits perfectly in a standard 60 cm under-sink cabinet or drawer.

With the 3/8” → 1/2” adapter set, it’s compatible with all standard EU faucets and hoses, so installation works seamlessly in most kitchens.

Replace your filter once every 12 months or after ~30 000 L, depending on local water quality and usage.

You’ll receive an email notification when it’s time to replace it.

👉 Order your replacement filter here

Replacing your PJURE filter is quick and simple:

1. Turn off the cold-water supply and open the faucet to release pressure.
2. Use the included wrench to unscrew the stainless-steel housing and remove the old cartridge.
3. Insert the new PJURE filter and tighten the housing securely.
4. Turn the water back on and flush for 5 minutes before use.

PJURE is designed to drastically reduce plastic waste.

Its stainless-steel housing is reusable for life, so you only replace the internal cartridge once a year — significantly cutting single-use plastic.

Unlike reverse-osmosis systems, PJURE produces no waste-water and requires no electricity, making it a low-impact and sustainable choice for everyday use.

PJURE includes a 2-year warranty.

Need help? Contact hello@mypjure.com — we’ll be happy to assist.